FOMAPAN R 100

Black-and-white slides from one roll: Foma's R-100 process — every bath, temperature and formula, scene by scene.

  • 1 Black-and-white slides: positives you project, not negatives
  • 2 Loupe for judging density and sharpness
  • 3 Light table: judge slides by transmitted light
  • Studio still life rendered and graded for negativo.es · numbered pins step through what you are looking at.

    THE FIRST IMAGE IS DESTROYED a positive from the tank

    Fomapan R 100 is a black-and-white reversal film, ISO 100/21° in process R-100. You develop a negative, bleach it away, fog what is left, and develop that into a slide.

    HOW TO READ IT A magnified slice of emulsion. The big frame plays the 6 stages in turn (19 s loop); the strip below shows them all at once and lights up the one that is playing. Light comes from above only over the left half — so the left half is the part of the scene that was bright.

    1 · Expose Latent image in the lit half.

    2 · 1st develop Exposed crystals → silver: a negative.

    3 · Bleach Dichromate dissolves that negative silver.

    4 · Re-expose Bulb fogs the remaining halide.

    5 · 2nd develop Remaining crystals → silver: a positive.

    6 · Fix Secures the image.

    Source: Foma — Fomapan R 100 technical data and R-100 process

    TWELVE STEPS about 100 minutes wet

    HOW TO READ IT The bar is the whole job, each colour one bath, widths to scale (96:30 in all). The white line plays it in 30 seconds; the caption below says which bath you are in.

  • 1st developer 9:30 LQR 1+10, 20 ± 0.5 °C, darkness — makes a negative
  • Wash 10:00 running water
  • Bleach FB-2 5:00 dissolves the negative silver
  • Wash 5:00
  • Clearing FB-3 3:00 removes the yellow stain
  • Wash 5:00 light allowed after this
  • Re-exposure 1:00 100 W at 1 m, 30 s per side
  • 2nd developer 9:00 the rest turns black: the positive
  • Wash 10:00
  • Fix FU-5 9:00
  • Final wash 30:00 30 min, then dry and mount
  • LOAD IN TOTAL DARKNESS

  • Load the spiral exactly as for negative film.
  • Foma: total darkness (or infrared) is required up to step 6 inclusive.
  • 1 · FIRST DEVELOPER

  • Fomadon LQR 1+10 (91 ml + 909 ml = 1 l).
  • Hold the temperature: 20 ± 0.5 °C.
  • Agitate as for negatives: continuously for the first 30 s, then 10 s each minute.
  • This step sets the density of the final slide. Precision here matters more than anywhere else.

    2 · WASH

  • Running water (or repeated fills) at 20 ± 3 °C.
  • 3 · BLEACH FB-2

  • 5 g potassium dichromate + 10 ml conc. sulphuric acid, water to 1 l — acid into water.
  • Agitate as before; the negative image disappears.
  • Dichromate is carcinogenic and toxic to reproduction. Gloves, goggles, ventilation. Spent bleach to hazardous waste.

    4 · WASH

  • Running water.
  • 5 · CLEARING BATH FB-3

  • 50 g potassium disulfite per litre.
  • Removes the yellow bleach stain.
  • 6 · WASH

  • Running water. After this, light is allowed.
  • 7 · SECOND EXPOSURE

  • Take the film out of the tank on its spiral, in water.
  • 100 W bulb at 1 m, 30 s each side, turning the spiral.
  • Alternative: Foma's chemical reversal bath, 5 min + 10 min wash.
  • 9 · SECOND DEVELOPER

  • Fomadon LQR 1+10 again, 20 ± 0.5 °C.
  • Everything left now turns black — the positive.
  • 10 · WASH

  • Running water.
  • 11 · FIX FU-5

  • 250 g sodium thiosulfate ·5H₂O + 25 g potassium disulfite per litre.
  • 12 · FINAL WASH AND DRY

  • 30 min running water at 20 ± 3 °C.
  • Hang to dry; cut and mount in 5 × 5 cm frames.
  • Source: Foma — Fomapan R 100 technical data and R-100 process

    PER LITRE OF WORKING SOLUTION

    BATH

    COMPONENT

    AMOUNT

    FB-2 bleach

    Potassium dichromate

    5.0 g

    Sulphuric acid, conc.

    10 ml

    Water to

    1000 ml

    FB-3 clearing

    Potassium disulfite

    50.0 g

    FU-5 fixer

    Sodium thiosulfate ·5H₂O

    250.0 g

    Potassium disulfite

    25.0 g

    Developer

    Fomadon LQR

    1+10

    Foma recommends distilled (or at least boiled) water.

    Source: Foma — Fomapan R 100 technical data and R-100 process

    BEFORE AND AFTER

    STATE

    TEMPERATURE

    RH

    Unexposed

    5–25 °C

    40–50 %

    Exposed, unprocessed

    4–18 °C

    < 60 %

    Finished slides

    ≤ 21 °C

    40–60 %

    Out of fridge / freezer

    wait ≈ 2 h / ≈ 6 h

    Source: Foma — Fomapan R 100 technical data and R-100 process

    The End

    NEGATIVO.ES · LAB № 1

    THE EVIDENCE — SOURCES

  • Foma — Fomapan R 100 technical data and R-100 process
  • NOTES

  • Times and figures come from the linked manufacturer documents; the sheet packed with your film or kit overrides this page.
  • Values marked "derived" are calculated from those documents.
  • Read each chemical's safety data sheet. Spent fixer carries dissolved silver — take it to a collection point.
  • All artwork generated for negativo.es. Independent site, not affiliated with any brand named.