PUSHED & PULLED

Latitude first, then push, pull and the clip test — with Ilford's own numbers showing how much longer each stop really takes.

  • 1 Pushed: shot at EI 1600 (+2)
  • 2 Pulled: shot at EI 50 (−1)
  • 3 Only the development time changes
  • Studio still life rendered and graded for negativo.es · numbered pins step through what you are looking at.

    OFTEN YOU CHANGE NOTHING the alibi you already have

    FILM

    MANUFACTURER SAYS

    Fomapan 100

    Good at 1 EV over (EI 50) and 2 EV under (EI 400) — no processing change

    Kodak Tri-X 400

    1 stop under: normal processing

    Ilford HP5 Plus

    Good quality from EI 400 to 3200 with adjusted development

    Ilford Delta 3200

    True speed ISO 1000; best EI 1600–6400

    Source: Foma — Fomapan 100 Classic technical data · Kodak F-4017 — Tri-X 320 & 400 technical data (2021) · Ilford HP5 Plus — technical information (Harman, 2018) · Ilford Delta 3200 — technical information (Harman, 2025)

    HOW TO READ IT Same film, three treatments: density (up) against scene brightness (right). Illustrative shape. • Grey: box speed, normal development. • Red (push): shadows sink, the curve steepens — more contrast. • Bone (pull): more light, shorter development — a flatter, softer curve with full shadows.

    WHAT EACH ONE DOES

    PUSH

  • Rate higher (EI × 2ⁿ), develop longer.
  • Contrast rises, grain grows, shadows thin out.
  • PULL

  • Rate lower (EI ÷ 2ⁿ), develop shorter.
  • Contrast falls, shadows hold; negatives look dense and soft.
  • ONE ROLL, ONE DECISION

  • Every frame on the roll gets the same development.
  • Mark film, EI and push/pull on the cassette immediately.
  • ILFORD'S RESCUE FOR A ROLL SHOT TOO SLOW

  • HP5 Plus accidentally exposed at low EI: Perceptol stock, 20 °C — 9 min at EI 50 or 100, 11 min at EI 200.
  • Ilford is clear this is a rescue, not equal quality.
  • Source: Ilford HP5 Plus — technical information (Harman, 2018)

    FOR A ROLL YOU'RE UNSURE OF sacrifice the head

    IN TOTAL DARKNESS, CUT THE HEAD

  • Pull a few frames' worth from the cassette and cut them off.
  • Put the rest back in a light-tight box or tank.
  • DEVELOP THE STRIP AT STANDARD TIME

  • Normal time, temperature and agitation for the film's box speed.
  • READ IT

  • Thin → give the rest more development.
  • Dense → give it less.
  • Normal → carry on unchanged.
  • DEVELOP THE REST

  • Corrected time; everything else unchanged.
  • HOW MUCH LONGER, REALLY from Ilford's own table

    HOW TO READ IT Each bar = Ilford's printed HP5 Plus time at that EI divided by its EI 400 time, per developer (derived). Bars grow in; colour = EI. • +1 stop (EI 800): from ×1.11 (DD-X) to ×1.5 (HC-110 B). • +2 stops (EI 1600): from ×1.44 to ×2.2. • No single multiplier works for every developer — use the printed time when there is one.

    Source: Ilford HP5 Plus — technical information (Harman, 2018)

    The End

    NEGATIVO.ES · LAB № 3

    THE EVIDENCE — SOURCES

  • Ilford HP5 Plus — technical information (Harman, 2018)
  • Kodak F-4017 — Tri-X 320 & 400 technical data (2021)
  • Ilford Delta 3200 — technical information (Harman, 2025)
  • Foma — Fomapan 100 Classic technical data
  • NOTES

  • Times and figures come from the linked manufacturer documents; the sheet packed with your film or kit overrides this page.
  • Values marked "derived" are calculated from those documents.
  • Read each chemical's safety data sheet. Spent fixer carries dissolved silver — take it to a collection point.
  • All artwork generated for negativo.es. Independent site, not affiliated with any brand named.