THE DARK ROOM

Developing your first black-and-white roll at home, scene by scene — Ilford's own recipe with every pour, inversion and drain spelled out.

  • 1 Daylight tank — loaded in total darkness, then used with the lights on
  • 2 DEV · STOP · FIX — labelled, always in that order
  • 3 Spiral reel: film winds in by ratcheting
  • 4 Negatives drying on weighted clips
  • 5 Thermometer: the developer must read 20 °C
  • Studio still life rendered and graded for negativo.es · numbered pins step through what you are looking at.

    MIX IT, WARM IT, LABEL IT the preparation

    MIX THREE WORKING SOLUTIONS

  • Developer: 60 ml Ilfotec DD-X + 240 ml water (1+4).
  • Stop: 15 ml Ilfostop + 285 ml water (1+19).
  • Fixer: 60 ml Rapid Fixer + 240 ml water (1+4).
  • Label each jug. Same order every time: DEV · STOP · FIX.
  • Fixer before developer erases the roll. Labels are not optional.

    BRING EVERYTHING TO 20 °C

  • Stand the three jugs in a water bath a couple of degrees warmer than 20 °C.
  • Check with the thermometer just before pouring the developer.
  • Stop, fix and wash may sit within ±5 °C of the developer.
  • A big jump between baths can crack the emulsion (reticulation).

    Source: Ilford — Processing your first black & white film (PDF) · Ilford HP5 Plus — technical information (Harman, 2018)

    LOADING THE SPIRAL the only blind part

    LIGHTS OUT — COMPLETELY

  • Changing bag or a room you have checked for leaks: sit 5 minutes in the dark — if you can see your hand, it isn't dark.
  • Lay out by touch: cassette, opener, scissors, dry spiral, tank, lid.
  • Even a safelight fogs panchromatic film. No light at all until the lid is on.

    OPEN THE CASSETTE

  • Pop the flat end off with the opener.
  • Slide the spool out; hold the film by its edges only.
  • SQUARE THE LEADER

  • Cut off the tongue-shaped leader straight across, between perforations.
  • Round the two corners slightly so they don't snag.
  • FEED THE SPIRAL

  • Entry lugs towards you; push about 5 cm under the ball bearings.
  • Ratchet the two halves back and forth — the film walks in by itself.
  • At the end, cut the film off the spool and give a few more turns.
  • The spiral must be bone dry. If it jams, back out a turn — never force it; kinks leave crescent marks.

    TANK CLOSED: LIGHTS ON

  • Spiral onto the centre column, into the tank, lid on until it clicks.
  • From here on everything happens in normal light.
  • Source: Ilford — Processing your first black & white film (PDF)

    BATH BY BATH with the lights on

    Ilford's worked example: Delta 100 in DD-X 1+4, 12 minutes at 20 °C. The bar shows the whole run to scale.

    HOW TO READ IT The bar is the whole job, each colour one bath, widths to scale (18:20 in all). The white line plays it in 24 seconds; the caption below says which bath you are in.

  • Developer 12:00 4 inversions in the first 10 s of every minute; pour out 15 s early
  • Stop 0:10 Ilfostop 1+19, invert twice, back in its bottle
  • Fix 3:00 Rapid Fixer 1+4, same agitation, reusable
  • Wash ×5 0:30 fill, 5 inversions, drain
  • Wash ×10 0:40 fill, 10 inversions, drain
  • Wash ×20 1:00 fill, 20 inversions, drain
  • Ilfotol 1:00 wetting agent 1+200, then hang
  • POUR IN THE DEVELOPER — START THE CLOCK

  • Pour smoothly and quickly through the light trap.
  • Start the timer the moment it is in.
  • AGITATE — ILFORD RHYTHM

  • 4 inversions in the first 10 seconds.
  • Then 4 inversions in the first 10 seconds of every minute.
  • Slow, full turns: upside down and back is one.
  • Too much agitation raises contrast; too little gives streaks. Keep the rhythm identical every roll.

    TAP AFTER EVERY AGITATION

  • Rap the tank firmly on the bench once or twice.
  • Dislodges air bubbles that would leave clear dots.
  • POUR OUT 15 SECONDS EARLY

  • Start draining 15 s before the time is up.
  • Developer is single-use: discard it.
  • STOP BATH

  • Pour in Ilfostop, invert twice.
  • Pour back into its bottle after at least 10 seconds (reusable).
  • FIX

  • Pour in Rapid Fixer and agitate with the same rhythm.
  • Minimum 3 minutes; pour back into its bottle — it is reusable.
  • Fixer is exhausted when clearing time is double that of fresh fixer (about 24 rolls per litre).

    WASH — THE ILFORD METHOD

  • Fill with water at 20 °C (±5), invert 5 times, drain.
  • Refill, invert 10 times, drain.
  • Refill, invert 20 times, drain.
  • WETTING AGENT

  • Last fill: water with 5 ml Ilfotol per litre (1+200).
  • Stir briefly, then take out the spiral.
  • HANG TO DRY

  • Weighted clip at the bottom, in a still, dust-free place.
  • Optionally run a clean squeegee or chamois down once, gently.
  • Hair dryer only on low, kept moving about 30 cm away.
  • READ THE NEGATIVE

  • Clear film rebates and legible edge numbers = chemistry worked.
  • Full tonal range = time and exposure were right.
  • Cut into strips of six (35 mm) and sleeve them.
  • OPTIONAL — A LIVE TIMER

    Invert 4 times, tap the tank.

    Calls every agitation and the early pour.

    Source: Ilford — Processing your first black & white film (PDF) · Ilford Rapid Fixer — technical information (PDF) · Ilford HP5 Plus — technical information (Harman, 2018)

    WHAT HAPPENED IN THE TANK silver, step by step

    HOW TO READ IT A magnified slice of emulsion. The big frame plays the 5 stages in turn (16 s loop); the strip below shows them all at once and lights up the one that is playing. Light comes from above only over the left half — so the left half is the part of the scene that was bright.

    1 · Expose Light marks the crystals it hits (latent image).

    2 · Develop Marked crystals become black metallic silver.

    3 · Stop Acid halts development instantly.

    4 · Fix Unexposed halide dissolves away.

    5 · Result Dark where the light was: a negative.

    WARMER IS FASTER Ilford's own example

    Ilford: 12 min at 20 °C = 8½ min at 23 °C = 17 min at 16 °C. Outside roughly 18–24 °C, warm or cool the bath instead of correcting time.

    BATH

    12-MINUTE FILM

    9-MINUTE FILM

    18 °C

    14:17

    10:43

    19 °C

    13:06

    9:49

    20 °C

    12:00

    9:00

    21 °C

    10:42

    8:01

    22 °C

    9:32

    7:09

    23 °C

    8:30

    6:22

    24 °C

    7:35

    5:41

    Rows other than 20 and 23 °C are derived from a curve through Ilford's three published points.

    Source: Ilford — Processing your first black & white film (PDF)

    WHAT WENT WRONG read the negative

    THE NEGATIVE LOOKS…

    CAUSE

    NEXT TIME

    Completely clear, no edge numbers

    Fixer before developer

    Label bottles

    Clear, edge numbers visible

    Film never exposed

    Check shutter, advance, lens cap

    Thin, grey, weak highlights

    Under-developed (short, cold, exhausted)

    Check time, temperature, dilution

    Dense, blocked highlights

    Over-developed / over-exposed

    Shorten development 10–20 %

    Clear dots

    Air bubbles

    Tap after each agitation

    Milky or purple

    Under-fixed

    Re-fix full time, re-wash

    Crescent marks

    Film kinked while loading

    Dry spiral, never force

    Source: Ilford — Processing your first black & white film (PDF)

    The End

    NEGATIVO.ES · LAB № 2

    THE EVIDENCE — SOURCES

  • Ilford — Processing your first black & white film (PDF)
  • Ilford HP5 Plus — technical information (Harman, 2018)
  • Ilford Rapid Fixer — technical information (PDF)
  • NOTES

  • Times and figures come from the linked manufacturer documents; the sheet packed with your film or kit overrides this page.
  • Values marked "derived" are calculated from those documents.
  • Read each chemical's safety data sheet. Spent fixer carries dissolved silver — take it to a collection point.
  • All artwork generated for negativo.es. Independent site, not affiliated with any brand named.