Back

Original PDF extract: 29 pages, ending at battery checking. Later chapters are missing.

Canon AV-1

Aperture Value. The camera Canon built because it was asked to.

An argument Canon lost on purpose

Why an aperture-priority body exists in a shutter-priority house

  1. By 1979 Canon had staked its automatic cameras on one belief: that shutter speed is the number a beginner understands. Freeze or blur — you can see the difference. The AE-1 and the A-1 were built on that belief, and it cost Canon money to hold it.
  2. Shutter-speed-priority automation was, in Canon's own account, the important one: users found shutter speeds easier to understand than aperture settings.
  3. It was also the expensive one to produce. Holding that line meant building the harder mechanism into every automatic body in the range.
  4. In America and other overseas markets, aperture-priority 35 mm cameras were simply the majority of what sold. Distributors asked for a model that matched.
  5. So Canon built one — and made it the cheap one. The AV-1 launched alongside a low-cost New FD 50 mm f/2 and a new quick mount.

One decision, two consequences

A working model of what the AV-1 does when you turn the aperture ring

  1. Aperture priority sounds like a convenience. It is really a statement about what matters: you are claiming that how much of the scene is sharp is the decision worth protecting, and that the exposure time can fall where it falls. The panel below is that trade, made literal. Choose a stop and watch both sides move.
  2. You set this
  3. Depth of field at the chosen distance
  4. The camera answers
  5. 1/500 1/512 required, set without steps

Fig. 2 ·  Steps 7, 8 and 9 of the booklet's quick start, printed here as a negative. Far right: the three marks the needle can point at  ·  page 9

What a stop is actually worth

50 mm lens · subject at 3 m · circle of confusion 0.03 mm

  1. Nine clicks of the ring take the sharp zone from a third of a metre to nearly twelve. That span is the whole reason to hand the shutter speed over to the camera: it is the only one of the two numbers that changes what the photograph is about .

Why the flash stops at 1/60

Four-axis, horizontal-travel focal-plane shutter with cloth curtains

  1. Slowed roughly a thousandfold, and the open phase at 1/60 is held a moment so the eye can catch it. The proportions between the four speeds are the point, not the absolute timings.
  2. The mechanism
  3. The AV-1 handles this by removing the choice: the X position on the Selector Dial locks the camera to the 1/60 flash setting regardless of what the meter thinks.

Three positions that are not f-stops

Everything the Selector Dial can do that isn't metered automation

  1. Automatic — the normal state
  2. You hold an f-stop; the camera chooses any speed between 2 s and 1/1000, without steps. There is no manual mode to fall back on and no shutter-priority mode at all.
  3. Flash — fixed at 1/60
  4. The sync setting. X-synchronised accessory shoe, no PC socket in the specification. A dedicated Speedlite will also hold the camera there and light the finder's flash-ready mark.
  5. Bulb — as long as you hold it
  6. The shutter stays open while the release is held. Everything beyond that — long time exposures on a tripod, a cable release into the socket in the release button — is yours to time, because the meter has nothing to say past 2 s.
  7. Fourth position
  8. Built in, with an adjustable delay and a blinking Self-Timer Lamp on the front. The blink is not decoration: it is the only confirmation you get, from in front of the camera, that the timer is actually counting.
  9. The one compensation
  10. There is no exposure-compensation dial. There is a Backlight Control Switch that adds about 1.5 stops in one fixed helping, beside the lens mount. For anything other than one and a half stops, the method is to lie to the ASA Film Speed Dial — half the film speed for one stop more light.

Load, advance, rewind

The mechanical half, where nothing is automatic at all

  1. The AV-1 cannot read the cartridge. DX coding did not exist yet — it arrives in 1983, four years after this camera — so the ASA Film Speed Dial is the only thing the meter knows about your film.
  2. ISO 25 – 1600 No DX contacts Lock button on the dial
  3. The take-up spool is slotted rather than self-threading. The check is the same as it has always been: both rows of perforations sitting on the sprocket teeth before the back closes.
  4. Confirm the rewind crank turns as you advance — the only proof the film is moving
  5. One full throw per frame, and the lever accepts partial strokes if your thumb cannot make the arc in one go. It rests 30 degrees out from the body, which is also the switch: pushed flush, the release is locked.
  6. Stroke 120° Standoff 30° Shutter Release Button Lock Lever
  7. The counter counts up, and resets itself the moment the back is opened. It is a count of advances, not of exposures — it has no way of knowing whether there was film in there.
  8. Additive counter Auto-reset on back opening
  9. Crank on the top plate. Release the clutch first, wind until the tension drops away, then open. Opening a back with film still across the gate is the one irreversible mistake on this list.
  10. Top-plate crank Label the cassette before it leaves your hand

Fig. 3 ·  The booklet's rear-and-base spread, pages 5 and 6, laid open the way it was printed. The Film Rewind Button is the small one on the base plate.

Six volts, or nothing at all

The original cell, what replaces it, and what a flat one looks like

  1. The AV-1 was specified for a 6 V 4G-13 mercury oxide cell, or a 4LR44 alkaline. The mercury cell is long gone, and for once that is not a problem: the replacements are the same nominal voltage, so the meter needs no correction. This camera escapes the trouble that ruins older bodies built around 1.35 V mercury cells, where an alkaline substitute reads wrong at every setting.
  2. With no usable cell the shutter stays locked and the advance lever will not move. Nothing on the AV-1 is mechanically timed — there is no emergency speed, not even B. A seized-feeling lever on a second-hand body is worth six volts of investigation before it is worth anything else.
  3. The Battery Check Button is its own small piece of design. Press it and the same needle that normally reads shutter speed swings to a battery index instead — one instrument, two jobs, no extra lamp. It is the cheap solution, and it is the right one.
  4. The instruction book is blunt about when to suspect the cell: after a new one is fitted, when the shutter will not function with the Selector Dial at A, when long exposures are frequent, in very cold weather, and simply when the camera has sat unused.
  5. Figs. 4 – 5 ·  The chamber, polarity printed inside its cover, and the Battery Check Button  ·  pages 27 and 29

Specification

As published by Canon, with present-day equivalents where the original is obsolete

  1. Not reduced, not hidden — never fitted. If you need to set both numbers, this is the wrong body and always was.
  2. The one omission that stings on an aperture-priority camera, since depth of field is the thing you are buying. The table above is the substitute.
  3. The scale in the finder is speeds. What you set, you are expected to remember — or to glance down at the ring.
  4. Every exposure, including B, runs on the battery. There is no fallback at all.
Loading Canon AV-1…