In the centre of the finder is a paler rectangle: the rangefinder patch , coupled to every M lens from 21 to 135 mm. Turn the focusing ring until the patch agrees with the rest of the view.
Coincidence — the double image merges into one. Works on anything, and the booklet prefers it for people. Split image — put a straight vertical line through the patch and make it continuous. In theory the more accurate of the two; ideal for buildings.
Cover the viewfinder window and only the bright-line frames and the patch remain visible.
Rangefinder — double image and broken line: out of focus
Fig. 13 — the finder photograph from the booklet; the patch is live
The trees across the lake sit at about 30 m. The second image is offset by the difference between the focused distance and the subject — the same geometry as a real base-length rangefinder, exaggerated for the screen.
Six focal lengths, three pairs
Mount a lens and its bayonet raises the right bright-line frame — always as a pair: 28 + 90 , 35 + 135 or 50 + 75 . The frames move with focusing to correct parallax , the offset between finder and lens.
The frames match a 23 × 35 mm slide-mount field at the closest distance; further away, the film gets a little more than the frame shows. The frame preselector lever on the front calls up any pair without changing lenses — to decide which lens the picture wants.
Frame preselector — lever (15) on the front
Frame sizes drawn in proportion to focal length within the same finder view; the real 28 mm frame runs close to the edge of the finder.
Two triangles, equally bright
The M6 meters through the lens at working aperture , off a white spot printed on the shutter curtain; a photodiode at about 11 o'clock inside the mount reads it. A light touch on the release turns the meter on for about 10 seconds — only with the shutter wound and the dial not on B.
Set the speed first, then turn the aperture ring until both triangles glow equally . A single triangle points the way to turn. Use only the marked speeds; in-between settings light the LEDs but read wrongly.
Switching the meter on — light pressure on the release
FINDER · BELOW THE IMAGE
Meter range at ISO 100: EV 0 to EV 20 (1 s at f/1 to 1/1000 at f/32). Speeds 1–1/1000 s, B; ISO 6–6400.
A circle two-thirds of the frame
The metering field is a central circle covering about 23 % of the frame for whatever lens is mounted. It is not marked in the finder; the booklet's reference: its diameter is about ⅔ of the short side of the bright-line frame , for every focal length.
That makes the M6 selective: point the circle at what matters. On sunlit sand or snow the meter sees mostly white and under-exposes — measure the shade or a mid-tone, or open up. The booklet's rule for pure white details: open up by two stops , for example 1/125 instead of 1/500; one stop is enough for light-coloured scenes.
Metering fields — 90, 21 and 28 mm; the grey circle is the measured area
Bright sand — measure an even mix of light and dark, or open up
Snow — measure the shade, or open up 1–2 stops
Load, hold, power
Loading. Remove the baseplate with its latch, open the hinged back, push the leader over the three-pronged take-up posts and drop the cartridge in. Replace the baseplate — its inner wheel straightens the film. Check: as you wind, the rewind knob turns backwards. Fire and wind twice to reach frame 1.
Holding. Right hand on the body, index finger on the release, thumb against the advance lever in its stand-off position; left hand under the lens; camera against the forehead. Turn the camera for verticals without moving your hands.
Rewinding. Turn the rewind lever to R, unfold the crank and turn clockwise.
Batteries. Two 1.55 V silver-oxide cells (SR44 / 357) or one 3 V lithium (DL 1/3 N). About 20 hours of metering — roughly 4,800 readings at 15 s each. Replace when the LEDs look weak; the readings stay accurate as long as they light at all. Keep the gold contacts inside the back clean and untouched.
No battery? The shutter is mechanical: every speed still works. Only the meter is gone.
Flash. Hot shoe and a sync socket; electronic flash at 1/50 (the lightning symbol on the dial) or slower.