Back

Pentax Spotmatic SP

The controls, as the booklet names them

Original instruction book, nomenclature pages · printed in a second colour, reproduced in it

  1. Figs. 1 – 2 ·  Front controls; film chamber with the back open

What averaging does to a subject

Left: a true spot reading of the subject. Right: the SP's centre-weighted average of the whole frame.

  1. Pick a scene. Both readings are developed below; the subject marker shows how far from mid-grey it lands. A bright surround drags the average up and the subject goes dark; a dark surround does the opposite.
  2. Spot reading of the subject EV 8.5
  3. f/4 · 1/60
  4. subject at mid-grey
  5. Spotmatic SP — centre-weighted average EV 13.5
  6. f/11 · 1/125
  7. subject 5 stops under
  8. Walk in until the subject fills the frame, centre the needle there, then step back and shoot at those settings without re-metering. The average is only correct when the frame is mostly the subject.

Metering, step by step

The booklet's sequence · the meter reads the ground glass, so focus comes first

  1. If the index on the shutter dial shows red, the speed and film-speed combination is outside the meter's range. Move to a faster or slower speed until it clears.
  2. Fig. 3 ·  Setting the shutter speed — step 3
  3. Try it — the finder at the working aperture
  4. Screen brightness relative to wide open: 100%

FP or X

Two terminals · the X mark sits on the 60 of the speed dial

  1. How to read it

Loading, film speed, double exposures

Load away from direct sunlight · 20 or 36 exposures

  1. Fig. 4 ·  The circles mark the perforations that must sit on the sprocket teeth; the inset shows the leader in the take-up spool slot
  2. Hold the lens square to the 42 mm thread and turn it backwards until the thread drops into step, then forwards. Stop at finger-tight.
  3. M42 × 1 mm Meter switch off while mounting
  4. Pull the rewind knob up to open the back. Insert the cartridge, push the knob down, lead the film into the take-up spool slot. Wind until both rows of perforations sit on the sprocket, close the back, and wind two blank frames.
  5. The rewind knob must turn as you wind — proof the film is moving
  6. Under the rewind knob: PANCHRO for black-and-white, a daylight or tungsten symbol for colour, EMPTY when unloaded. It is a reminder only. To check whether film is loaded, turn the rewind knob clockwise: if it turns freely, the camera is empty.
  7. PANCHRO · COLOR · EMPTY
  8. After the first exposure, turn the rewind knob to take up slack and hold it. Press the rewind release button on the base and work the wind lever: the shutter cocks without the film moving. Shoot. Then make one blank exposure before the next frame.
  9. From the instruction book, "Multiple exposure"
  10. Press the rewind release on the base and crank in the arrow direction until the tension drops. The release button turns while the film is rewinding.
  11. Open the back only after the tension drops
  12. The ASA–DIN scale on the dial, and the ISO equivalent
  13. Fig. 5 ·  Modern ISO combines both: the arithmetic number is ASA, the degree is DIN. Each 3° DIN is one stop.

Battery: check and replace

Mallory PX-400 / RM-400-R, 1.35 V mercury · powers the meter only

  1. Check, per the booklet
  2. The cover is on the base plate and opens with a coin. The cell goes in with the (+) side toward the top of the camera. Handle it by the edges with a dry cloth: skin acid damages it. Switch the meter off whenever you are not reading it — left on, it drains the cell quickly.
  3. Replacing the mercury cell today
  4. Whatever you fit, run the check above, then compare the meter with one you trust at a bright and a dim reading.

Specification

From the instruction book's specification pages

  1. Fig. 6 ·  ASA window in the shutter dial · "cocked" indicator · film reminder dial
Loading Pentax Spotmatic SP…