Back

Yashica Mat-124G

Look down. Slow down.

The controls

Instruction book, description of parts · front and side

  1. Fig. 1 ·  Front: viewing lens above, taking lens below; aperture and shutter speed set on the two dials between them
  2. The frame is 56 × 56 mm — 3,136 mm², 3.6 times a 35 mm frame. There is no vertical or horizontal; composition happens inside the square.

Focusing on the ground glass

Mirror and no prism: the image is reversed left to right

  1. Fig. 2 ·  In focus (top) and out of focus (bottom), as the booklet shows them on the screen
  2. What you do with the camera
  3. What the ground glass shows

Parallax

The taking lens is below the viewing lens, so close up it sees a lower frame

  1. Green: what the finder showed · orange: what the film got
  2. At the chosen distance
  3. 7.8% of the frame height is shifted
  4. Close up, frame with a little room at the top — or after framing, raise the camera by the distance between the two lenses before releasing.

Loading 120 or 220

Same width, different thickness — set the pressure plate first

  1. Fig. 3 ·  Side controls; open back with the film pressure plate and the "Start" marks
  2. Cross-section through the film gate
  3. Why the plate moves
  4. Turn the Back Cover Locking Ring; the back springs open and the counter resets to "S". Pull out the upper Spool Holder Knob, place the empty spool in the take-up chamber, push the knob back.
  5. Counter: S = start
  6. Hold the back with both hands and slide the plate with your thumbs until it clicks and the window shows 12 EX. for 120 or 24 EX. for 220. Press the plate once or twice to check the spring.
  7. Green = 120 Red = 220
  8. Put the new roll in the lower chamber (pull out the lower Spool Holder Knob). Insert the leader straight and fully into the take-up spool slot, then turn the crank gently to check it winds evenly.
  9. A skewed leader fogs the edges
  10. Wind until the arrow on the backing paper meets the green ▲ mark for 120 or the red ▲ mark for 220. Close the back and lock the ring.
  11. Check the lug sits in the latch slot
  12. Turn the crank forward until it stops and "1" shows in the counter, then back to cock the shutter. At slow speeds let the shutter finish before winding.
  13. One forward + one back stroke per frame
  14. After frame 12 (or 24), keep winding until the backing paper is fully on the take-up spool. Open the back, remove the roll keeping the paper tight, seal it.
  15. No rewind on this camera
  16. Figs. 4 and 6 ·  Instruction booklet

Roll in the lower chamber, leader into the take-up spool

Closing the back; shutter lock at "L"

Leaf shutter, flash, self-timer

Copal-SV · between the lens elements · MX synchroniser

  1. The blades open from the centre, so the whole frame is exposed at once at every speed. Electronic flash therefore synchronises up to 1/500.
  2. Flash connects through the PC contact; mount the unit on the accessory shoe or a bracket on the tripod socket. Aperture = guide number for your film speed ÷ distance.
  3. Wind to cock the shutter, set the self-timer lever, press the release: the shutter fires after 6–15 s. The booklet warns that operating the self-timer lever with the selector on M can damage the self-timer.

Metering and battery

CdS match-needle · shutter speed set first · ASA 25 to 400

  1. Fig. 5 ·  ASA window · speed and aperture windows
  2. Battery
  3. Meter only — the shutter works without it. The booklet specifies a 1.3 V mercury cell, Mallory PX-13B or Eveready EPX-13 (the PX625 size). Open the compartment cover by turning it anticlockwise.

Specification

From the instruction book's "Features"

    Loading Yashica Mat-124G…